Last week, a homeowner in Poole contacted me for his annual boiler service. I asked if there were any problems he had experienced that I should be privy to. He mentioned that it was taking much longer than usual to get hot water and after running a test, some radiators were not warming up a room sufficiently. I assured him that I would be at his property within the hour to conduct the service and attend to any faults.
I got to the client’s home in 45 minutes despite some light traffic. I started by running the boiler to pinpoint any issues and the first thing that struck me was the noise being produced. It was not very loud and might have even gone unnoticed but it was an indicator of a common problem for boilers.
I also opened up the boiler to check the fan air pressure and the gas pressure. The fan air pressure was quite low and this might have been the cause of the sub-optimal operation. I looked closely at the spark electrodes and realized they had oxidized thus cleaning them would not help much. The best option would be a replacement. When I looked at the heat exchanger, I noticed there was limescale buildup which is why the fan air pressure had dropped significantly. Boiler repairs in Dorset often entail sludge or limescale removal due to the hard water in the area. I connected the boiler to a power flush machine which helped clear the limescale from the primary heat exchanger. The limescale in the plate heat exchanger was cleared using a chemical cleaning solution. After 3 hours, the entire process was complete and we fired up the boiler for a test. Not only had the “kettling” subsided, but adequate heat was coming from all the radiators in the property.
Last week, we had a customer from the BH8 area reach out to us requesting her annual boiler service after realizing her water was taking longer to heat up.
I drove to Oxford Road and arrived within the hour to conduct the service. The boiler was a Worcester Bosch Greenstar 40 CDi, and I started by running it to identify any flaws. Indeed, the water was taking longer to heat up, and some rooms were not receiving enough heat. I also bled the radiators and realized the water had a slightly brownish hue which indicated limescale build-up in the tubes. The filters had also corroded which can be attributed to the low water alkalinity in Bournemouth.
To clear out the limescale, I prepared a power flush which broke down the limescale deposits and cleared the corrosion.
I also added a water softener component to her boiler, which would prevent the limescale buildup from happening again. The process took about four hours and we bled the radiators a second time. This time the water did not appear discoloured, and we were sure that the limescale was completely gone.
Whether you are looking to soak up some sun during the summer or escape the debilitating winter cold, holiday time is exciting, especially given that most of us are only just getting the opportunity to travel post covid. Holidays also come with a lot of preparation beforehand such as packing, travel plans and ensuring the home is left in the best condition. Homeowners often wonder what to do with their central heating systems especially if they are traveling during the winter. We will be answering a popular question asked by many homeowners “Should I turn my boiler off when I go on holiday?”
Summer holidays vs winter holidays
The season in which you are travelling determines if you should turn your boiler off or leave it on. If you plan to travel during the summer, then you might get away with switching off your boiler.
During the winter, however, it is recommended you do not completely switch off your boiler. While there might be some cost-saving benefits to having the boiler off, the risks involved far outweigh the reward and you might spend a lot more on damaged pipes or the boiler. Here are some of the benefits of leaving your boiler on when you leave for a holiday:
Prevent Frozen Indoor Pipes
During the winter, temperatures in the UK and many other countries drop below zero degrees at which point, water starts to freeze and expand. Pipes in insulated areas or along the exterior walls of your house are susceptible to cracks or bursts from the expansion of frozen water. Leaving your boiler on while on holiday keeps the water moving and above the freezing point.
Cracked or busted pipes result in leaks and could you imagine returning home from a holiday to a flooded house?
Cracked or busted pipes can also be very expensive to repair. There have been instances of homeowners spending upwards of £7,000 on repairs. This cost could add up from the damaged items and the inconvenience of searching for accommodation elsewhere as the plumbers conduct repairs. For cabinets that house plumbing pipes, it is advisable to leave this open such that heat can reach them to prevent freezing.
Avoid the Risk of a Damaged Boiler
Leaving your boiler off can result in the internal pipes getting frozen and damaged. Switching off your boiler can also result in internal leaks and the risk of irreversible damage is very high. Even if your boiler does not get to the point of replacement, there is a likelihood of its efficiency being compromised even after a repair. Aside from the damaged pipes, the valves and pumps could also seize up which potentially leads to central heating problems down the road.
Return home to a warm house
Getting back from holiday to an ice-cold house can be a huge downer especially if you had travelled to a warm area. Other than preventing leaks and property damage, leaving your boiler on also ensures you return home to a warm house and you can settle back in quicker. As a bonus, you enjoy your holiday much more knowing everything back home is well taken care of.
Best Practices to Leaving Your Boiler On
Realistically, you should not leave your boiler on 24/7 or at high temperatures since there is nobody home. So, how do you ensure your home has sufficient warmth without wasting energy and piling up your energy bills?
Establish a Schedule
You should establish a routine where you switch on your boiler for a few hours every day you are on holiday. In the UK, the coldest hours of the day during the winter range between 2 A.M and 5 A.M. It is especially important to have your boiler on during these cold hours. You could also run the boiler a few other times during the day to keep everything flowing.
Utilize your thermostat
A thermostat is an invaluable device you should invest and the beauty of thermostats is they can now be operated remotely through an app. A programmable thermostat enables you to regulate the hours your central heating is on and you can also regulate the temperature of your home. When you are away on holiday, a temperature of 15 – 18 degrees Celsius is ideal to keep the pipes and the boiler warm. Unless you live in a very cold area, avoid pushing the temperature beyond 20 degrees as this could increase your energy bills unnecessarily. These thermostats are an absolute must-have nowadays, which is why we install them with almost all of out boiler installations in Bournemouth or Poole.
Prioritize rooms that need the most heat
Thermostats enable you to control the temperature of a room independently. Spaces such as the basement tend to house sump pumps which can freeze up and result in mould growth. If your boiler is in a cold room such as the loft or the basement, then you should prioritize heating these areas to keep the pipes around the boiler in optimal temperature.
COST-SAVING TIPS WHILE ON HOLIDAY
The majority of homeowners switch off their boilers while away as they are concerned about their energy bills. There are some tips you can implement to save on costs while your boiler is routinely on during the winter. The biggest cost you will save on, however, is the expensive repairs and replacements from completely switching your boiler off.
Close all Windows and Doors before leaving
Other than preventing burglars from visiting your property, closing all windows and doors ensures cold air does not rush into your home. The rooms also retain more heat and your boiler does not have to work extra hard or long to heat up a room. Additionally, properly sealing the doors and windows also retains more heat in your home.
Frost Protection Thermostats
Modern boilers often come with an anti-freeze/anti-frost component that protects the internal pipework of the boiler. For boilers that might not have this component, investing in a frost protection thermostat is advisable. Frost protection basically works by keeping the water in your boiler above 5 Degrees Celsius. When the sensor detects water temperature has dropped below 5 Degrees, the boiler heats the water back up to 10 Degrees Celsius then goes off. At Senior Plumbing, we are specialists in Viessman boilers which have built-in frost protection thermostats.
Insulate your home
Insulating your home is a great way to retain heat in your property and prevent cold air from seeping through the cold walls of the house. You could insulate your home using thermal paper or spray foam. The additional benefit of insulating your property is the savings extend beyond your holiday period.
If you are looking for something more temporary, you could insulate indoor pipes to prevent exposure to the cold. If you have a regular or system boiler, you could insulate your hot water tank since the water starts to cool down rapidly. Insulating your hot water tank slows
down the cooling rate and prevents the boiler from reheating the water again.
Leaving your boiler switched on while you are on holiday is a good idea and with most modern boilers there should be no risks involved. For your peace of mind, we recommend servicing your boiler before you leave if you haven’t done so within the last year or so.
Getting a boiler can be a daunting process for homeowners, but we want to make it as stress-free as possible for our Bournemouth and Poole residents. Some boiler installations are priced too low which leaves you questioning why they are so cheap, while others might try to rip you off. And as the price of purchasing and installing a boiler is one of the most important elements in deciding which supplier or installer you go for, we thought we should provide you with the average cost of boilers throughout the Bournemouth/Poole area.
These are typical standalone prices we have seen, based on local research and years in the industry.
A budget standalone Combination boiler such as an Ideal Logic Combi C24 is likely to start from £750 in Bournemouth. The warranty is an important factor to look out for and this type of boiler, as it only sits around the 2-year mark.
A mid-range boiler such as Worcester Bosch Greenstar 28CDi Compact comes with a warranty of up to 10 years and prices start from £1000.
A premium boiler with more output such as the Viessmann Vitodens 200-W B2KE 35kW starts from £1600 and also has a 10-year warranty.
Boiler prices in Poole are on average slightly higher but still reasonable.
The budget boiler would for instance start at around £800,
The mid-range boilers such as the Worcester Bosch Greenstar 28CDi Compact would start at £1100 – £1200
A Premium boiler such as a Viessmann Vitodens 200-W B2KE 35kW would start at around £1700.
In case you are wondering what a combi boiler is, this is an advanced boiler that works without a hot water cylinder, therefore, provides instant heat. It efficiently serves houses with up to 2 bathrooms and 10 radiators.
Standalone System Boiler Price
If you have a larger house with more bathrooms, then you might consider getting a system boiler.
A simple standalone system boiler in Bournemouth such as a Baxi 618 18kW starts from £839 and comes with a 7-year warranty.
A similar mid-range boiler with a 7-year warranty, such as a Vaillant ecoFIT Pure 618 starts at £1058.
Premium boilers such as the Viessmann Vitodens 200-W B2HE 32kW with a 10-year warranty are likely to start from £1650.
Once again, the boiler prices in Poole tend to be higher in most areas. For instance, a simple 18kW boiler such as the Baxi 618 18kW might have prices starting from £889.
A mid-range boiler such as the Worcester Greenstar Life 35kW has a 12-year warranty and costs around £1357
Standalone Conventional Boiler Price
Conventional boilers are ideal for very large properties or where multiple bathrooms are often used simultaneously.
Simple conventional standalone boilers such as a Baxi 430 Heat 30kW start at £800 in Bournemouth and comes with a standard warranty of at least 5 years.
A mid-range conventional boiler such as a Worcester Bosch Greenstar 18Ri starts at £870 and comes with a 10-year warranty.
A premium boiler such as a Viessmann Vitodens 100-W Compact WB1B 26kW with a 10-year warranty starts at £950 in Bournemouth.
Most Baxi 400 Heat boilers range from £850 to £940 in Poole.
A conventional boiler such as a Worcester Bosch Greenstar 18Ri starts at £900 and comes with a 10-year warranty.
A top tier Viessman boiler starts at £1105. It is unlikely to find such boilers priced above £1110.
BOILER INSTALLATION PRICES IN BOURNEMOUTH AND POOLE
Boiler installations prices in Bournemouth and Poole vary between £999-4000 depending on the project scope and the location. Typically installers will charge slightly more for Poole residents. Although at Senior Plumbing and heating we keep our prices consistent throughout.
We would typically suggest to stay clear of any installers which offer very cheap prices, as often they won’t have had the experience to make sure your boiler is going to be running as efficient as possible, which will only cost you more in the long run.
To give a rough ballpark of installation costs:
Budget combi installations: £999-£1400
Mid range combi installations: £1400-2200
Premium combi installations: £2200-3400
System or Regular boilers are going to be similar prices, but the job will vary greatly depending on the requirements. Typically they will range anywhere between £1,700 – £4,000.
What impacts the installation price
Flue exit – If you have a round horizontal flue, then you might not have a significant additional cost. If, however, your home requires a vertical flue or you need to brick up a square flue, then the costs might go up. If your project involves a flue alteration, then the cost in Bournemouth and Poole is likely to range between £300 – £500 depending on the scope.
If a replacement is taking place – prices are likely to go up considering the labour your engineers will require in pulling down the previous boiler and installing the new one.
A boiler conversion – this could be costly, especially if the project involves decommissioning the previous boiler to install a different one. In this case, a new flue might have to be installed and some alterations involving the plumbing such as the feed tanks will have to be made.
Hot water cylinder installation – If you are upgrading from a Combi boiler to a Conventional or Regular boiler, then you might need a hot water cylinder for storage. Hot water cylinders in Bournemouth and Poole start from £300 with premium cylinders starting at £500. In both towns, it is very rare to find a cylinder priced above £1000.
Hopefully this give you a good idea the rough prices installers and suppliers offer throughout Dorset and in particular Bournemouth and Poole. As stated previously, we never fluctuate on price, so if you want an upfront free quote for a top quality installation give us a call
Tackle Sludge and Sedimentation Build Up in Boilers with Magna Cleanse in Bournemouth
Has your boiler been acting up lately? Do you find cold spots in your radiator or hear banging noises? If so, chances are that your boiler has sedimentation or sludge build-up that is affecting its ability to heat your home.
Now, you might instantly think that the best solution to get rid of this issue is to replace your old boiler and get a new boiler installation. If your boiler is old and hence it is acting up like this, you should certainly consider replacing the boiler. However, if your boiler is relatively new, you don’t need to replace it. Instead, you can most likely fix it through a getting your boiler Magna Cleansed.
Firstly, what is Magna Cleanse and what are the exact signs you need Magna Cleanse?
What is Magna Cleanse?
During Magna Cleanse, chemically treated water is pumped through the pipes and radiators using a purpose-built machine. This chemical-treated water is meant to break down the sludge and sediment deposits in your boiler and radiators. This process is referred to as a power flush.
This process is quite effective in removing dirt and sludge built up. An average Magna Cleanse treatment costs about ₤300-₤950. The costs also depend on the number of radiators you have in your home. At Senior Plumbing and Heating you can find our prices here, but if you are short on time we do a power flush at around £45 per radiator.
Signs that Indicate you Need Magna Cleanse
Reduced heat transfer from the radiators
Sludge and sediment build up at the bottom of radiators resulting in cold spots that tend to get bigger over time.
Noticeably discoloured water during bleeding of radiators.
Radiator pipes are always hot whether the system stays warm or cool.
To heat the home, your boiler is working extra hard
Banging or knocking noise coming from your boilers, radiators, or pipes
Whistling of the boiler due to overheating parts
If you have a combi boiler, sludge or sediment build-up can result in warm water in the taps.
Consequences of ignoring the problem
If you neglect this sludge or sediment build-up, it can cause further problems in your system.
It will be expensive to run and maintain the boiler and radiator system.
The system will struggle to heat the home
‘Wet’ parts of the boiler might get damaged by the loose debris
Due to heat exchanger blocks, the water will be warm instead of hot from your combi boiler
If your system is corroded, it might cause a leak
You might require a complete replacement of radiators and pipework.
Moreover, you may also need to replace your boiler and get a new boiler installation for your home. And this can be a hefty investment you might not be willing to make.
Alternative Options to Magna Cleanse
Magna Cleanse is certainly the best way to clean the sludge and sedimentation build-up in your boiler, radiators, and pipes. But the costs of Magna Cleanse might deter you from opting for this treatment.
If you don’t want to use Magna Cleanse as the treatment process, you can also go for a chemical cleanse or magnetic filter.
Chemical cleanse includes putting a chemical in the boiler or radiator and leaving it for a few hours or days. This removes any mild sludge or sediment build-up in the boiler. The remains can be washed out by putting water through the system. You can do such cleanse regularly to avoid excessive build-up.
A magnetic filter is also a great option to tackle loose or mild debris in the radiator. This is something we often insist on installing when completing a customer annual boiler service.
Yes, these two alternatives are cheap but are not as effective as Magna Cleanse in the long term. Though it is costly, it will help you keep your boiler or radiator clean and working efficiently.
Tips to Book a Professional Magna Cleanse Services
Most machine manufacturers give a certificate to the engineer. Make sure you ask to see that.
Choose a Magna Cleanse engineer that has received training from the machine manufacturer company. This will ensure high-quality services.
If you have been looking for effective Magna Cleanse service in Poole or Bournemouth, you can get in touch with Senior Plumbing and heating. We provide Magna Cleanse services but also provide a wide range of boiler, gas and heating services.
We provide Magna Cleanse services during the installation process along with any time you need to tackle the sludge build-up in your boiler and radiator.
Given the weather the other day, it was a surprise to get a call regarding a boiler breakdown for one of the local shops right in the center of Bournemouth. The shop owner said they were trying to wash up in the back, but their boiler seemed to be playing up and they were struggling to get any hot water flowing through.
I popped round about midday to have a look and it seemed that their Greenstar 40 cdi classic had been left without a service for way too long and they had a huge build-up of sediment and sludge which was preventing the boiler from functioning properly. This is typically why I insist on all my customers getting an annual boiler service, to make sure everything is ticking over correctly and so they avoid having to get an installation when the boiler could have been functioning for many more years to come. The system was so dirty that the pipe had probably reduced to about 10mm from an original 22mm. On top of this the boiler pressure seemed to be faily low, around 1.0 bar, which I then worked out was due to a leak, caused by corrosion.
After a long conversation with the customer, we decided that installing a new combi boiler was the best decision as this boiler would cost a lot to get back functioning, would likely only last 2-5 more years and be more costly on energy bills. I need to head back in a few days to install their new Viessmann, but above are the images from the boiler inspection and should be a warning to anyone looking to avoid a boiler service!
Last week, a customer from Bournemouth on Roslin Road (BH3), called up as they were having issues with their boiler. They were unsure if it was a boiler repair or boiler installation that they needed. On the phone, she informed me that they were experiencing a rumbling and whistling sound from their boiler. I asked if it sounded like the noise that a kettle makes and she said that it did. I knew from this that their boiler was kettling and this was what was causing the issues.
I explained that the water inside your boiler should not reach boiling point. It starts to boil if the water passes through the flame too slowly. This is caused by a blockage in the pipework. You will hear the result of this when the boiler starts to make sounds that are similar to a kettle boiling. We booked her boiler repair service for the next day.
When I arrived to inspect the boiler, I knew that there was a build-up of sludge blocking the system and raising the temperature of the water inside. This is most likely caused by a build-up of magnetite – an iron-based chemical that wears off the insides of radiators. To fix the issue, I took apart the heat exchanger and cleaned it to clear the blockage. The water then started to flow freely through the pipes and stay at the optimum temperature.
These photos show a picture of a boiler installation we did last week in Parkstone, BH12. The customer had had a boiler for about 10 years but it was starting to break down.
They had a boiler repair a year ago when their boiler failed to produce hot water for their showers and the radiators were not working at all. I wondered why there were already more problems with the boiler and so I asked about their boiler servicing. It turns out that they had never had a boiler service and barely looked after their boiler over the last 10 years. This was the reason that they have had to get a new boiler and the repair last year was not good enough.
When we got to the property we removed the oldi boiler and began their boiler installation. The whole process took 4 hours because we had to change the old central heating system. Their new Viessmann combi boiler will provide their whole family with hot water. We informed them about the benefits of getting regular boiler services which will ensure their boiler lasts longer and healthier life
These photos show the work I did for a customer in Sterte, BH15. They called me up wanting a power flush and boiler service. They were experiencing some issues with their radiator temperature. Their boiler installation was carried out by me about 3 years ago, so they contacted me again to help them out.
When describing their problem on the phone, I told them that a power flush is an excellent way to clear out the system and ensure that your central heating system is working effectively. We booked their service for the next day.
When we arrived at the property, we got started on the boiler service. We took apart the casing of the boiler elements and inspected them. We cleaned the necessary parts and checked for any leakage – there were none. All the boiler parts seemed to be working well when we checked them for wear and tear. We then inspected the pipes for the power lush, there was a lot of build-up of sludge and so I knew that this was where their radiator issue was coming from. We did the power flush using Adey MC1 Central Heating System Protector. The sludge was removed so that their radiators were due to work perfectly again. The boiler service we provided gives them peace of mind knowing that there are no small issues with their boiler, and doing this regularly will guarantee to lengthen their boiler’s life
Customer story, central heating service – BH14 in Parkstone
One of my regular customers from BH14 in Parkstone called in about a problem with their underfloor heating. They noticed that in certain areas, their floors were not heating up as they would like. We made an appointment to come and take a look at their heating system and boiler for the next day.
It turns out that their thermostat heads were leaking.
When I got to the property, it was obvious that this leak had caused a lack of pressure, which created failures to the underflooring heating system. I found the source of the leak by testing out each zone separately. When doing this, I discovered that there were quite a few areas that were leaking. Luckily, we got to the case before a more serious leak occurred and changed all the leaking thermostat heads.
After the job was completed, I carried out a safety check to double-check that all parts of the thermostat were working efficiently.